Rhino-Rack Aero Roof Rack Installation - 2013 Chrysler 200 DA126- Video

Today on our 2013 Chrysler 200, we'll be test fitting the Rhino-Rack 2500 Series Roof Rack with Aero crossbars 50 inches long in silver part number DA126. We'll also be using the Rhino-Rack part Fit Kit part number DK317. With our roof rack system assembled according to the instructions, we'll begin our test fit by opening both front doors, then we'll grab our front bar and place it under the front part of our roof. To make sure we have these aligned in the correct location, we need to measure 28 centimeters from the center of the door jam to the center of our leg foot plate. We'll do this measurement on both sides to ensure that our feet are in line with each other. We can then use the Allen key to tighten down the Allen bolt on the inside of the Flip pac to secure our clamps around the roof line of our vehicle. We'll do this on both sides of the vehicle until we have our front bar full secured. more

Watch Video

11/5/2013 10:00:22 AM

Rhino-Rack Aero Roof Rack Installation - 2013 Chrysler 200- Video

Today on our 2013 Chrysler 200, well be test fitting the Rhino-Rack 2500 Series Roof Rack with Aero Crossbars, 50" long in black, part number DA126B. Well also be using our Fit Kit, part number DK317. With our roof rack system assembled according to the instructions, well begin our test fit by opening our front doors. Well grab our front bar and place it onto the front part of our roof. To make sure that we have this bar in the right location, well measure 28 cm from the center of our doorjamb, to the center of our foot plate. Well do this measurement on both sides to ensure that our feet are in line with each other. Well use an Allen key to tight down our Allen bolt, which will secure our clamps around the roofline of our vehicle. Well do this for both sides of our front bar. more

Watch Video

11/5/2013 10:00:22 AM

Rhino-Rack Euro Square Roof Rack Installation - 2013 Chrysler 200- Video

Today on our 2013 Chrysler 200, well be test-fitting the Rhino Rack square bars 2500 series Roof Rack, 49 inches long, using part number DS126B, and the fit kit DK317. With our roof rack system assembled according to the instructions, well begin our test fit by opening our front doors. Well grab our front bar, and place it unto the front part of our roof. To make sure that we have this bar in the correct location, we need to measure 28 centimeters from the center of the door jam to the center of our footplate. Well do this measurement on both sides to ensure that out feet are inline with each other.Then we can use the Allen key to tighten down our Allen bolt, which will secure our clamp around the roofline of our vehicle. Well make our way from side to side tightening it a little at a time, to make sure we dont lose our position. more

Watch Video

11/5/2013 10:00:22 AM

Rhino-Rack Heavy-Duty Roof Rack Installation - 2013 Chrysler 200- Video

Today on our 2013 Chrysler 200, well be test-fitting the Rhino Rack 2500 series Roof Rack, with the heavy duty crossbars 50 inches long in silver, using part number DH1250S, and DK317 for our fit kit. With our roof rack assembled according to the instructions, well begin our test fit by opening both front doors. Well grab our front bar and place it under the front part of our roof. To ensure that we have this bar in the correct location, we need to measure 28 centimeters from the center of the door jam to the center of our footplate. Well do this measurement on both sides to ensure that out feet are inline with each other.Then well use an Allen tool to tighten down our Allen bolt, which will secure our fit around the roofline of our car. Well make our way back and forth tightening a little out of time, so we dont lose our position. more

Watch Video

11/5/2013 10:00:22 AM

Yakima Q Tower Roof Rack Installation - 2013 Chrysler 200- Video

Today on our 2013 Chrysler 200 well be test fitting the Yakima Round Bar Roof Rack System, part numbers Y00409, Y00696, Y00606, and Y00124. With our crossbars already assembled according the Yakima fit lookup or the included instructions well place the front crossbar onto the vehicle. Well then need to measure from the front part of the glass to the first part of the tower. This measurement is included again in the Yakima fit lookup or the included instructions. Well measure eight inches on the drivers side and passenger side of the vehicle to make sure that the crossbar is perpendicular to the vehicle. Once weve established this position onto the roof or our vehicle, well tighten down the bolt on the inside of the tower and secure the tower by clamping down the black plastic cap. more

Watch Video

3/28/2013 12:06:27 PM

  1